- #ALTERA USB BLASTER WINDOWS 7 64 BIT HOW TO#
- #ALTERA USB BLASTER WINDOWS 7 64 BIT INSTALL#
- #ALTERA USB BLASTER WINDOWS 7 64 BIT SERIAL#
- #ALTERA USB BLASTER WINDOWS 7 64 BIT DRIVERS#
sof file to the MAX 10 device first, then download the pof file into the device with the board keeping powering on.Ĩ. pof file to the MA10 device (for self-designed board), it failed and reported the following errors, why did this happen?Ī:It may be caused by the MAX10 device. And you can use either of the Quartus software version later than 10.1 to work with the Windows 10 64-bit.Ħ. Q: What is the operating temperature specification of the UBT?Ī:The UBT is designed to operate in the commercial temperature range (0 to 85C).ĥ.Q: Will USB-Blaster work under Windows 10 64-bit?Ī: Yes, the USB-Blaster work under Windows 10 64-bit. Please note that UBT can't detect the JTAG chain on the Intel Arria 10 GX FPGA Development Kit.Ĥ. Q: What is the difference between the UBT and Altera USB Blaster Download Cable (UBA)?Ī: The main difference is the JTAG circuit, Terasic UBT supports JTAG voltage 2.5v~3.3V, the Altera USB Blaster supports 1.8V~3.3V, they are compatible with other features. Q: What is the TCK Clock Frequency for UBT and AUB2 respectively?Ī: The USB Blaster Cable works with the Jtag clock 6M, while the USB Blaster II Cable works at 24M.ģ. The AUB2 (USB-Blaster II Download Cable) supports USB Blaster II circuit and JTAG Voltage: 5.0-V TTL, 3.3-V LVTTL/LVCMOS ,Single-ended I/O standards from 1.5 V to 3.3 V.Ĭustomers can refer to Intel Cyclone 10 LP device handbook: and check your board JTAG voltage to see which cable is compatible with their board.Ģ. Q:What is the difference between UBT and AUB2?Ī: The main difference is the JTAG circuit, the UBT(USB Blaster Download Cable) supports USB Blaster I circuit and JTAG Voltage: 2.5V ~ 3.3V. The Quartus version you installed: Q16.1 or others.ġ.Whether you tested follow the above processes.PC OS version: Win10-32bit or Win7-64bit or Linux-64bit.b.Test with another usb blaster cable.Ĭ.If still with the same problem, please contact our technical support team via and provide below information: ii.If step i is OK: a.Test with another PC to see if the OS can detect unknown device. I.Make sure the board power is on and the port on board which connected to PC is USB blaster port.
![altera usb blaster windows 7 64 bit altera usb blaster windows 7 64 bit](https://www.mouser.com/images/marketingid/2013/img/157928474.png)
#ALTERA USB BLASTER WINDOWS 7 64 BIT INSTALL#
If yes, please install the USB blaster driver refer to this link: Altera USB Blaster Driver Installation Instructions
#ALTERA USB BLASTER WINDOWS 7 64 BIT SERIAL#
#ALTERA USB BLASTER WINDOWS 7 64 BIT HOW TO#
This section describes users how to test whether the on-board USB blaster or USB blaster cable is properly installed and operated
![altera usb blaster windows 7 64 bit altera usb blaster windows 7 64 bit](https://tomverbeure.github.io/assets/jtag/terasic_vs_cheap_clone.jpg)
Using USB Blaster Under Linux USB Blaster Self Test
![altera usb blaster windows 7 64 bit altera usb blaster windows 7 64 bit](https://techsmagic.com/wp-content/uploads/2021/01/USB-Blaster-Driver.png)
Prime Signal Tap Logic Analyzer for logic analysis.Īltera_USB_Blaster_Driver_Installation_Instructions You can also use the cable with the Intel Quartus The Terasic Download Cable and initiate the programming or configuration using To program or configure the device, connect the host system to the device board using
![altera usb blaster windows 7 64 bit altera usb blaster windows 7 64 bit](https://images-na.ssl-images-amazon.com/images/I/41DbpeCGYaL._SY355_.jpg)
System and set up the hardware in the Intel Quartus® Prime software.
#ALTERA USB BLASTER WINDOWS 7 64 BIT DRIVERS#
To start using the Intel FPGA Download Cable, user need to install the drivers on your Target power supplied by the device boardĭimension of the Terasic USB Download Cable The following picture and table list the pins of the Terasic Download Cable female plug andĭescribes their functions in the JTAG and passive serial modes. Table 1‑4 Support Target board supply voltage Support Target board supply voltage